Omnia Volt
DBX 676 Tube Mic Pre Channel Strip
DBX 286S Microphone Pre-amp Processor
The dbx® 286s is a full-featured Channel Strip Processor that provides a studio-quality microphone/instrument preamp and four processors that can be used independently or in any combination. Why microphone vocals and instruments through a noisy, fuzzy mixer? The sonically flawless dbx 286s Mic Preamp has all the features you need, including a wide range of input gain controls, switchable 48V phantom power and an 80Hz high-pass filter to remove low-frequency hum, rumble or wind. Use the patented dbx OverEasy compressor® to transparently smooth out uneven acoustic tracks or deliver that classic "in your face" vocal performance that only a dbx compressor can. Eliminate vocal sibilance and high-frequency distortion from instruments such as cymbals with the frequency-tunable De-Esser. Fine-tune the Enhancer HF Detail control to add sparkle and sharpness to your tracks, and make adjustments to the LF Detail control to add fullness and depth to vocals and bass instruments while cleaning up muddy low mids. And separate threshold and ratio controls on the Expander/Gate let you subtly reduce headphone leakage or radically shield loud guitar amps.
DBX 560A Compressor/Limiter
The dbx 560A Compressor/Limiter offers legendary VCA-based compression in the increasingly popular 500-series format. dbx has a storied history with modular processors dating back to our 900 series, and the 560A continues that tradition.
With the same switch-selectable OverEasy® and Hard Knee compression curves as our industry standard dbx 160A rackmount processor, the dbx 560A becomes your new workhorse compressor! With extremely wide threshold, ratio and output controls and true RMS level detection that provides the most natural sounding dynamic processing available, the 560A offers punch to drums, bass, vocals, almost everything! It is also versatile enough to go from subtle compression to "brick wall" peak mitigation.
M!ka Table Through Mount
M!ka Table Clamp
The M!ka Table Clamp or table clamp from M!ka, is one of the plug-in options to attach your M!ka arm to your desk. It can be combined with the M!ka microphone arm or the M!ka EasyLift monitor arm. Use the table clamp to attach your M!ka arm to the edge of your desk. Attach the M!ka table clamp to your desk, place the yellow spacer on top and slide in the M!ka arm of your choice. To make the M!ka table clamp fit snugly on your desk, simply place the M!ka table clamp at the edge of your table and twist the top and bottom parts together. The table clamp fits any table with a panel thickness of 18-74mm. Important, never use it on curved surfaces. It may slip off.
M!ka System Pole Desktop Mounting Kit
M!ka Table Top Mount
M!ka PopShield
M!ka Pole Cable Clamps (6x)
M!ka Wall Bracket
The M!ka wall bracket serves as a slide-in mount to attach M!ka arms to the walls of your room. Use it to mount M!ka microphone arms, M!ka EasyLift monitor arms or M!ka Studiolight. Drill four holes in your wall and attach the M!ka Wall Bracket to the wall of your room with the four included plugs and screws. Next, place the Yellow Spacer on the adapter and then slide in the M!ka arm of your choice. Importantly, zorg make sure your walls fixtures are suitable to carry the load.
M!ka Monitor Arm Cable Clamp (10x)
M!ka Cable Clamps help you achieve clean cable routing. Choose the cable clamp for M!ka monitor arms to secure your monitor's cables with the cable clamp. Use them for clean and unobtrusive cable routing along your M!ka monitor arms.As a spare part, you get the M!ka cable clamp for M!ka monitor arms in a polybag containing 10 pieces. Each M!ka monitor arm is supplied with two cable clamps upon purchase.
M!ka Yellow Intermediate Ring (10x)
The M!ka Yellow Spacer serves as a buffer between your M!ka arm and the various M!ka mounting adapters. Always use M!ka arms with a yellow spacer to achieve smooth changes in the position of your M!ka arm. In addition to the M!ka socket, each mount for M!ka microphone arms, M!ka EasyLift and M!ka Studiolight requires a yellow spacer between the M!ka arm and the adapter. Between the M!ka arm and the M!ka system pole, you also need a yellow spacer.As a spare part, you get the M!ka Yellow Spacer in a 10-piece polybag. Each mounting adapter for M!ka arms and each M!ka System Pole Desktop Mounting Kit already comes with a required yellow spacer.